System Settings#
Start#
Manual Instructions#
This manual includes symbology settings, function settings (lighting, keyboard type and factory reset, etc.) and interface settings. If you need to change the functions you need, just scan the configuration according to the Parameter Barcode below. All with (*) indicate factory default values.
Version Information#
Scan the “Version Information” Parameter Barcode to allow the host to quickly read the current device version.
Version Information#
Parameter Barcode Scanning#
By turning on the Parameter Barcode function, you can configure the parameters of the Scan Engine by scanning the Parameter Barcode.
Note
When modifying the configuration through the Parameter Barcode, the entire current flag bit list will be saved to the memory, that is, the configuration configured through the serial port but not saved will also be saved together.
Disable# |
* Enable# |
Transmit Parameter Barcode Data#
Whether to output the Parameter Barcode content, you can configure the parameters of the Scan Engine by scanning the following Parameter Barcode.
* Disable# |
Enable# |
User Default Settings#
Save Current Configuration As User Default# |
Restore User Factory Default Settings# |
Users can save their frequently used configurations as user default settings. By scanning “Save current settings as user default settings”, the current configuration information of the device can be saved as user default settings information. After this operation, the new configuration information will replace the original user default settings information. By scanning “Restore User Default Settings”, the Scan Engine can be switched to user default settings.
Power Control#
Sleep Mode#
This parameter determines the power mode of the module. In sleep mode, the Scan Engine enters sleep state as much as possible (can be awakened by wake-up command)
* Sleep Mode#
Continuous Working Mode#
In continuous working mode, the Scan Engine is still awake after each decoding attempt.
Continuous Working Mode#
Lighting And Aiming#
Illumination#
The lighting can provide auxiliary lighting for shooting and reading, and the beam shines on the reading target, improving the reading performance and the ability to adapt to weak ambient light. Users can set it to one of the following states according to the application environment:
Normal lighting (default setting): The lighting lights up when shooting and reading, and turns off at other times;
The lighting is always on: the lighting will continue to glow after the Scan Engine is turned on;
No lighting: The light does not come on under any circumstances.
*Normal Lighting# |
No Lighting# |
Lighting Always On# |
AIM#
The projected aiming beam helps users find the optimal reading distance when shooting for reading. According to the application environment, users can
Choose any of the modes below.
Aiming Normal (default setting): The Scan Engine only projects the aiming beam when shooting and reading;
Aiming always on: After the Scan Engine is powered on, it will continue to project the aiming beam;
No Aiming: The aiming beam is extinguished under any circumstances.
* AIM For Normal# |
No Aiming# |
AIM For Constant Light# |
Prompt Output#
Beep Related#
Buzzer Type#
Scan the following Parameter Barcode to set the buzzer as a passive or active buzzer.
* Passive# |
Active# |
Volume Level#
Users can adjust the buzzer volume according to the application environment and personal habits by Scanning the following Parameter Barcode.
Mute# |
Bass# |
Alto# |
* Treble# |
Power-on Beep#
Disable# |
* Enable# |
Parameter Entry Beep#
Disable# |
* Enable# |
Decode Beep#
Disable# |
* Enable# |
Decode Beeper Tone#
The resonant frequency of the buzzer used by the user may be different from the default frequency. You can adjust the frequency of the decoding beep by scanning the following Parameter Barcode. Default is 2700Hz.
Scan the “Buzzer Frequency” Parameter Barcode
Buzzer Frequency#
Scan the “Numeric Barcode”. For example, if the frequency is 1500Hz, sweep 1, 5, 0, 0; if the frequency is 2700Hz, sweep 2, 7, 0, 0
Scan the “OK” Parameter Barcode to complete the setup.
Sure#
Decode Beep Quick Setting#
1000Hz# |
1500Hz# |
2000Hz# |
2500Hz# |
*2700Hz# |
3000Hz# |
3500Hz# |
Decode Beep Duration#
Users can set the duration of the decoding beep as needed, the default is 50ms.
Scan the “Beep Sound Duration” Parameter Barcode
Beeper Duration#
Scan the “Numeric Barcode”. For example, if the duration is 50ms, scan 5,0; if the duration is 200ms, scan 2,0,0
Scan the “OK” Parameter Barcode to complete the setup.
Sure#
Quickly Set The Decode Beep Duration#
30ms# |
*50ms# |
70ms# |
100ms# |
200ms# |
300ms# |
Reminder Light Related#
Alert Light Function Type#
* Decoding Hints# |
Power Prompt# |
Decode Success Indicator#
Disable# |
* Enable# |
Decoding Success Prompt Light Control Method#
Mode 0: long off after power on, on when decoding is successful, on for a specified time and then off.
Method 1: Always on when power is on, off when decoding is successful, and on after a specified period of time.
* Mode 0# |
Way 1# |
Decoding Status NR Output#
NR is the abbreviation of No Read. Before releasing the Trigger Button, if the barcode cannot be decoded within the timeout period, the “NR” message is allowed to be output; when this function is disabled, no message can be output to the host even if the barcode cannot be decoded.
* Disable# |
Enable# |